01-11-2014, 10:23 PM
Hello everyone!
Over the holidays I was gifted a 29 (actually 28 and change--unless my math is messed up) gallon aquarium: 30 long, 18 high, 12 deep. My original intent was a Holothele incei (terrestrial pygmy tarantula) colony, but I knew when I flipped the tank on its side that I would need to make an arboreal tank out of it instead--there's just something about tall tanks! This, combined with my love for frogs and slices of jungle, led me to PDFs. A few weeks later, after obsessive research, I started the "dirty work" of repurposing the tank. Here are some pics from the first few weeks of my build. I will continue to post as the project progresses, and am open to any and all constructive comments. Thanks for reading!
[ATTACHMENT NOT FOUND]
I used the usual GS + Silicone + Coir 3D background technique, but with a twist. Being a "multi-purpose" kinda gal, I knew I wanted the background to be fully removable in the future. I didn't want to use egg crate and didn't have a styrofoam backing board on hand, so I used the "bag method" and lined the part of the tank the background would be situated in with plastic bags. I then figured out the placement for my manzanita driftwood and suspended it in place with tape, wrapping areas that would be embedded in the foam--again, making each piece totally modular. Then it was only a matter of emptying two cans of GS into the tank.
Lessons learned this step: Thin layers of GS work best! Although I didn't attempt to build it up too much, I did run into issues with the backside. Because it was unable to expand back into the glass, I ended up having to pull it out of the tank after a few hours and slowly work the bag back while misting water to help the curing process. Ultimately, it worked just fine--and yes, it cured all the way through and separated from the bag nicely--but it did take some extra work and time. The back was also not perfectly square once I pulled it and allowed it to expand and thus, it needed to be trimmed.
[ATTACHMENT NOT FOUND]
[ATTACHMENT NOT FOUND]
[ATTACHMENT NOT FOUND]
Next I siliconed my substrates onto the fully cured GS. I chose to mix Eco Earth (fine coir) and coconut chips for a more rugged look. I went in stages and went over each section multiple times to ensure even coverage.
Lessons learned this step: All those cool little nooks and crannies I made with the GS? Yeah, they got covered pretty well. Also, thick beads of silicone will not necessarily spread and join one another, DO use a gloved hand to spread it around in an even layer to eliminate the need for touch-ups--I figured this out by the third section or so. Also, every single tutorial says it takes a lot of silicone, and I was no exception!
[ATTACHMENT NOT FOUND]
Now comes the hard part: waiting. I let everything sit for quite some time between steps. The silicone + coir step took a few days and I let it sit for a few more before moving on.
I siliconed the substrate dam in place using aquarium silicone--I used 3/32" glass from Lowe's that the kindly gent in the glass department cut for me (not pictured). I also siliconed around the inner rim of what used to be the tank top. The side door will be a 17 incher with a silicone hinge at the bottom; the top 5 inches will be screened for ventilation--my experience with DIY tarantula enclosures has taught me that it is infinitely easier to add water than remove it, so I always err on the side of too much ventilation.
Once the background had cured, I trimmed as necessary with a sharp knife. I found that the combination of shrinkage and expansion from the back meant I had to cut it square again so it would fit nicely against what was now my back wall. I cleaned any extra coir from the back so it wouldn't be trapped against the glass and cause a mold problem, then laid down a relatively thick bead of silicone all the way around the edge of the coated portion of the background, making sure I got a seal between the glass and the foam. Now, in the event I want to remove the background, all I need to do is run a razor around the edge and pull it out. I went ahead and pressed some coir into this silicone as well. I left the tank in a horizontal position with weight on the background, and let it sit overnight and through the next day. When I flipped it right side up, it was solid as a rock. I then cleaned up the edges with a razor but didn't stress too hard, knowing that plants would obscure most imperfections.
[ATTACHMENT NOT FOUND]
[ATTACHMENT NOT FOUND]
After another few days, I installed my drainage layer, substrate mix, and wood. I moved the tank to its final location--but still need a base for it, argh!--before completing this step, as I am using gravel rather than LECA or Hydroton. I installed a double-folded nylon mesh substrate barrier and several inches of my own ABG mix: coir, peat moss, coconut chips, and sphagnum. The plants seem to really enjoy it and a near-death Peperomia (sp. Cupid?) has perked up since being planted in it. Lastly, I installed the wood by wedging the pieces into the background and against each other. The pieces that had been used during the GS step fit nicely into their "pockets" as intended and are pretty bulletproof.
[ATTACHMENT NOT FOUND]
[ATTACHMENT NOT FOUND]
[ATTACHMENT NOT FOUND]
Now the fun part: planting! This is the only pic I have of the planted tank, and I've since rearranged quite a bit. I need bromeliads, more Peperomia, and I'm on the hunt for some decent and varied ground cover as well *hint, hint*
[ATTACHMENT NOT FOUND]
I still need to add leaf litter (in the freezer atm) and seed with springtails, and, as I said, I may tear out the plants in favor of something more biotopic, but I'm pleased with the overall results. More tweaking will most certainly take place, but I don't intend on adding frogs for another few months at least.
Miscellaneous build notes:
Wood is local manzanita that has been baked at 300 degrees (F) for one hour and allowed to sit in the oven while it cools. On that note, leaf litter is also manzanita that was sorted, trimmed, boiled for a few minutes, and frozen for a few days.
Rocks were soaked in a 10% bleach solution and rinsed several times with hot running water.
Plants were processed per the generally accepted bleach dunk and cool water rinse.
Lighting will be a single 6500K CFL in a dome fixture that directs all light down into the terrarium--I may also add a fan to cool things down as necessary.
Misting will be done by hand for the time being.
Current inhabitants: Philodendron pothos, Peperomia sp. Cupid, English ivy--the stalk variety, and a Seleirolia cultivar.
Intended vertebrate inhabitants: Ranitomeya ventrimaculata trio, with the intent of allowing in-vivarium breeding and tad rearing.
Like I said, any constructive comments are welcome!
Over the holidays I was gifted a 29 (actually 28 and change--unless my math is messed up) gallon aquarium: 30 long, 18 high, 12 deep. My original intent was a Holothele incei (terrestrial pygmy tarantula) colony, but I knew when I flipped the tank on its side that I would need to make an arboreal tank out of it instead--there's just something about tall tanks! This, combined with my love for frogs and slices of jungle, led me to PDFs. A few weeks later, after obsessive research, I started the "dirty work" of repurposing the tank. Here are some pics from the first few weeks of my build. I will continue to post as the project progresses, and am open to any and all constructive comments. Thanks for reading!
[ATTACHMENT NOT FOUND]
I used the usual GS + Silicone + Coir 3D background technique, but with a twist. Being a "multi-purpose" kinda gal, I knew I wanted the background to be fully removable in the future. I didn't want to use egg crate and didn't have a styrofoam backing board on hand, so I used the "bag method" and lined the part of the tank the background would be situated in with plastic bags. I then figured out the placement for my manzanita driftwood and suspended it in place with tape, wrapping areas that would be embedded in the foam--again, making each piece totally modular. Then it was only a matter of emptying two cans of GS into the tank.
Lessons learned this step: Thin layers of GS work best! Although I didn't attempt to build it up too much, I did run into issues with the backside. Because it was unable to expand back into the glass, I ended up having to pull it out of the tank after a few hours and slowly work the bag back while misting water to help the curing process. Ultimately, it worked just fine--and yes, it cured all the way through and separated from the bag nicely--but it did take some extra work and time. The back was also not perfectly square once I pulled it and allowed it to expand and thus, it needed to be trimmed.
[ATTACHMENT NOT FOUND]
[ATTACHMENT NOT FOUND]
[ATTACHMENT NOT FOUND]
Next I siliconed my substrates onto the fully cured GS. I chose to mix Eco Earth (fine coir) and coconut chips for a more rugged look. I went in stages and went over each section multiple times to ensure even coverage.
Lessons learned this step: All those cool little nooks and crannies I made with the GS? Yeah, they got covered pretty well. Also, thick beads of silicone will not necessarily spread and join one another, DO use a gloved hand to spread it around in an even layer to eliminate the need for touch-ups--I figured this out by the third section or so. Also, every single tutorial says it takes a lot of silicone, and I was no exception!
[ATTACHMENT NOT FOUND]
Now comes the hard part: waiting. I let everything sit for quite some time between steps. The silicone + coir step took a few days and I let it sit for a few more before moving on.
I siliconed the substrate dam in place using aquarium silicone--I used 3/32" glass from Lowe's that the kindly gent in the glass department cut for me (not pictured). I also siliconed around the inner rim of what used to be the tank top. The side door will be a 17 incher with a silicone hinge at the bottom; the top 5 inches will be screened for ventilation--my experience with DIY tarantula enclosures has taught me that it is infinitely easier to add water than remove it, so I always err on the side of too much ventilation.
Once the background had cured, I trimmed as necessary with a sharp knife. I found that the combination of shrinkage and expansion from the back meant I had to cut it square again so it would fit nicely against what was now my back wall. I cleaned any extra coir from the back so it wouldn't be trapped against the glass and cause a mold problem, then laid down a relatively thick bead of silicone all the way around the edge of the coated portion of the background, making sure I got a seal between the glass and the foam. Now, in the event I want to remove the background, all I need to do is run a razor around the edge and pull it out. I went ahead and pressed some coir into this silicone as well. I left the tank in a horizontal position with weight on the background, and let it sit overnight and through the next day. When I flipped it right side up, it was solid as a rock. I then cleaned up the edges with a razor but didn't stress too hard, knowing that plants would obscure most imperfections.
[ATTACHMENT NOT FOUND]
[ATTACHMENT NOT FOUND]
After another few days, I installed my drainage layer, substrate mix, and wood. I moved the tank to its final location--but still need a base for it, argh!--before completing this step, as I am using gravel rather than LECA or Hydroton. I installed a double-folded nylon mesh substrate barrier and several inches of my own ABG mix: coir, peat moss, coconut chips, and sphagnum. The plants seem to really enjoy it and a near-death Peperomia (sp. Cupid?) has perked up since being planted in it. Lastly, I installed the wood by wedging the pieces into the background and against each other. The pieces that had been used during the GS step fit nicely into their "pockets" as intended and are pretty bulletproof.
[ATTACHMENT NOT FOUND]
[ATTACHMENT NOT FOUND]
[ATTACHMENT NOT FOUND]
Now the fun part: planting! This is the only pic I have of the planted tank, and I've since rearranged quite a bit. I need bromeliads, more Peperomia, and I'm on the hunt for some decent and varied ground cover as well *hint, hint*
[ATTACHMENT NOT FOUND]
I still need to add leaf litter (in the freezer atm) and seed with springtails, and, as I said, I may tear out the plants in favor of something more biotopic, but I'm pleased with the overall results. More tweaking will most certainly take place, but I don't intend on adding frogs for another few months at least.
Miscellaneous build notes:
Wood is local manzanita that has been baked at 300 degrees (F) for one hour and allowed to sit in the oven while it cools. On that note, leaf litter is also manzanita that was sorted, trimmed, boiled for a few minutes, and frozen for a few days.
Rocks were soaked in a 10% bleach solution and rinsed several times with hot running water.
Plants were processed per the generally accepted bleach dunk and cool water rinse.
Lighting will be a single 6500K CFL in a dome fixture that directs all light down into the terrarium--I may also add a fan to cool things down as necessary.
Misting will be done by hand for the time being.
Current inhabitants: Philodendron pothos, Peperomia sp. Cupid, English ivy--the stalk variety, and a Seleirolia cultivar.
Intended vertebrate inhabitants: Ranitomeya ventrimaculata trio, with the intent of allowing in-vivarium breeding and tad rearing.
Like I said, any constructive comments are welcome!
[Enter witty signature here]